| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: fix fanout UAF in packet_release() via NETDEV_UP race
`packet_release()` has a race window where `NETDEV_UP` can re-register a
socket into a fanout group's `arr[]` array. The re-registration is not
cleaned up by `fanout_release()`, leaving a dangling pointer in the fanout
array.
`packet_release()` does NOT zero `po->num` in its `bind_lock` section.
After releasing `bind_lock`, `po->num` is still non-zero and `po->ifindex`
still matches the bound device. A concurrent `packet_notifier(NETDEV_UP)`
that already found the socket in `sklist` can re-register the hook.
For fanout sockets, this re-registration calls `__fanout_link(sk, po)`
which adds the socket back into `f->arr[]` and increments `f->num_members`,
but does NOT increment `f->sk_ref`.
The fix sets `po->num` to zero in `packet_release` while `bind_lock` is
held to prevent NETDEV_UP from linking, preventing the race window.
This bug was found following an additional audit with Claude Code based
on CVE-2025-38617. |
| In the Linux kernel, the following vulnerability has been resolved:
udp: Fix wildcard bind conflict check when using hash2
When binding a udp_sock to a local address and port, UDP uses
two hashes (udptable->hash and udptable->hash2) for collision
detection. The current code switches to "hash2" when
hslot->count > 10.
"hash2" is keyed by local address and local port.
"hash" is keyed by local port only.
The issue can be shown in the following bind sequence (pseudo code):
bind(fd1, "[fd00::1]:8888")
bind(fd2, "[fd00::2]:8888")
bind(fd3, "[fd00::3]:8888")
bind(fd4, "[fd00::4]:8888")
bind(fd5, "[fd00::5]:8888")
bind(fd6, "[fd00::6]:8888")
bind(fd7, "[fd00::7]:8888")
bind(fd8, "[fd00::8]:8888")
bind(fd9, "[fd00::9]:8888")
bind(fd10, "[fd00::10]:8888")
/* Correctly return -EADDRINUSE because "hash" is used
* instead of "hash2". udp_lib_lport_inuse() detects the
* conflict.
*/
bind(fail_fd, "[::]:8888")
/* After one more socket is bound to "[fd00::11]:8888",
* hslot->count exceeds 10 and "hash2" is used instead.
*/
bind(fd11, "[fd00::11]:8888")
bind(fail_fd, "[::]:8888") /* succeeds unexpectedly */
The same issue applies to the IPv4 wildcard address "0.0.0.0"
and the IPv4-mapped wildcard address "::ffff:0.0.0.0". For
example, if there are existing sockets bound to
"192.168.1.[1-11]:8888", then binding "0.0.0.0:8888" or
"[::ffff:0.0.0.0]:8888" can also miss the conflict when
hslot->count > 10.
TCP inet_csk_get_port() already has the correct check in
inet_use_bhash2_on_bind(). Rename it to
inet_use_hash2_on_bind() and move it to inet_hashtables.h
so udp.c can reuse it in this fix. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: serialize btintel_hw_error() with hci_req_sync_lock
btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET
and Intel exception-info retrieval) without holding
hci_req_sync_lock(). This lets it race against
hci_dev_do_close() -> btintel_shutdown_combined(), which also runs
__hci_cmd_sync() under the same lock. When both paths manipulate
hdev->req_status/req_rsp concurrently, the close path may free the
response skb first, and the still-running hw_error path hits a
slab-use-after-free in kfree_skb().
Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it
is serialized with every other synchronous HCI command issuer.
Below is the data race report and the kasan report:
BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined
read of hdev->req_rsp at net/bluetooth/hci_sync.c:199
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254
hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030
write/free by task ioctl/22580:
btintel_shutdown_combined+0xd0/0x360
drivers/bluetooth/btintel.c:3648
hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246
hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526
BUG: KASAN: slab-use-after-free in
sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202
Read of size 4 at addr ffff888144a738dc
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_expect: skip expectations in other netns via proc
Skip expectations that do not reside in this netns.
Similar to e77e6ff502ea ("netfilter: conntrack: do not dump other netns's
conntrack entries via proc"). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: use netlink policy range checks
Replace manual range and mask validations with netlink policy
annotations in ctnetlink code paths, so that the netlink core rejects
invalid values early and can generate extack errors.
- CTA_PROTOINFO_TCP_STATE: reject values > TCP_CONNTRACK_SYN_SENT2 at
policy level, removing the manual >= TCP_CONNTRACK_MAX check.
- CTA_PROTOINFO_TCP_WSCALE_ORIGINAL/REPLY: reject values > TCP_MAX_WSCALE
(14). The normal TCP option parsing path already clamps to this value,
but the ctnetlink path accepted 0-255, causing undefined behavior when
used as a u32 shift count.
- CTA_FILTER_ORIG_FLAGS/REPLY_FLAGS: use NLA_POLICY_MASK with
CTA_FILTER_F_ALL, removing the manual mask checks.
- CTA_EXPECT_FLAGS: use NLA_POLICY_MASK with NF_CT_EXPECT_MASK, adding
a new mask define grouping all valid expect flags.
Extracted from a broader nf-next patch by Florian Westphal, scoped to
ctnetlink for the fixes tree. |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: use the current queue number for stats
There's a potential mismatch between the memory reserved for statistics
and the amount of memory written.
gem_get_sset_count() correctly computes the number of stats based on the
active queues, whereas gem_get_ethtool_stats() indiscriminately copies
data using the maximum number of queues, and in the case the number of
active queues is less than MACB_MAX_QUEUES, this results in a OOB write
as observed in the KASAN splat.
==================================================================
BUG: KASAN: vmalloc-out-of-bounds in gem_get_ethtool_stats+0x54/0x78
[macb]
Write of size 760 at addr ffff80008080b000 by task ethtool/1027
CPU: [...]
Tainted: [E]=UNSIGNED_MODULE
Hardware name: raspberrypi rpi/rpi, BIOS 2025.10 10/01/2025
Call trace:
show_stack+0x20/0x38 (C)
dump_stack_lvl+0x80/0xf8
print_report+0x384/0x5e0
kasan_report+0xa0/0xf0
kasan_check_range+0xe8/0x190
__asan_memcpy+0x54/0x98
gem_get_ethtool_stats+0x54/0x78 [macb
926c13f3af83b0c6fe64badb21ec87d5e93fcf65]
dev_ethtool+0x1220/0x38c0
dev_ioctl+0x4ac/0xca8
sock_do_ioctl+0x170/0x1d8
sock_ioctl+0x484/0x5d8
__arm64_sys_ioctl+0x12c/0x1b8
invoke_syscall+0xd4/0x258
el0_svc_common.constprop.0+0xb4/0x240
do_el0_svc+0x48/0x68
el0_svc+0x40/0xf8
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1b0/0x1b8
The buggy address belongs to a 1-page vmalloc region starting at
0xffff80008080b000 allocated at dev_ethtool+0x11f0/0x38c0
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000
index:0xffff00000a333000 pfn:0xa333
flags: 0x7fffc000000000(node=0|zone=0|lastcpupid=0x1ffff)
raw: 007fffc000000000 0000000000000000 dead000000000122 0000000000000000
raw: ffff00000a333000 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff80008080b080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff80008080b100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff80008080b180: 00 00 00 00 00 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffff80008080b200: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffff80008080b280: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
==================================================================
Fix it by making sure the copied size only considers the active number of
queues. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Do not skip unrelated mode changes in DSC validation
Starting with commit 17ce8a6907f7 ("drm/amd/display: Add dsc pre-validation in
atomic check"), amdgpu resets the CRTC state mode_changed flag to false when
recomputing the DSC configuration results in no timing change for a particular
stream.
However, this is incorrect in scenarios where a change in MST/DSC configuration
happens in the same KMS commit as another (unrelated) mode change. For example,
the integrated panel of a laptop may be configured differently (e.g., HDR
enabled/disabled) depending on whether external screens are attached. In this
case, plugging in external DP-MST screens may result in the mode_changed flag
being dropped incorrectly for the integrated panel if its DSC configuration
did not change during precomputation in pre_validate_dsc().
At this point, however, dm_update_crtc_state() has already created new streams
for CRTCs with DSC-independent mode changes. In turn,
amdgpu_dm_commit_streams() will never release the old stream, resulting in a
memory leak. amdgpu_dm_atomic_commit_tail() will never acquire a reference to
the new stream either, which manifests as a use-after-free when the stream gets
disabled later on:
BUG: KASAN: use-after-free in dc_stream_release+0x25/0x90 [amdgpu]
Write of size 4 at addr ffff88813d836524 by task kworker/9:9/29977
Workqueue: events drm_mode_rmfb_work_fn
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0xa0
print_address_description.constprop.0+0x88/0x320
? dc_stream_release+0x25/0x90 [amdgpu]
print_report+0xfc/0x1ff
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x225/0x4e0
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_report+0xe1/0x180
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_check_range+0x125/0x200
dc_stream_release+0x25/0x90 [amdgpu]
dc_state_destruct+0x14d/0x5c0 [amdgpu]
dc_state_release.part.0+0x4e/0x130 [amdgpu]
dm_atomic_destroy_state+0x3f/0x70 [amdgpu]
drm_atomic_state_default_clear+0x8ee/0xf30
? drm_mode_object_put.part.0+0xb1/0x130
__drm_atomic_state_free+0x15c/0x2d0
atomic_remove_fb+0x67e/0x980
Since there is no reliable way of figuring out whether a CRTC has unrelated
mode changes pending at the time of DSC validation, remember the value of the
mode_changed flag from before the point where a CRTC was marked as potentially
affected by a change in DSC configuration. Reset the mode_changed flag to this
earlier value instead in pre_validate_dsc().
(cherry picked from commit cc7c7121ae082b7b82891baa7280f1ff2608f22b) |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-fsl-lpspi: fix teardown order issue (UAF)
There is a teardown order issue in the driver. The SPI controller is
registered using devm_spi_register_controller(), which delays
unregistration of the SPI controller until after the fsl_lpspi_remove()
function returns.
As the fsl_lpspi_remove() function synchronously tears down the DMA
channels, a running SPI transfer triggers the following NULL pointer
dereference due to use after free:
| fsl_lpspi 42550000.spi: I/O Error in DMA RX
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[...]
| Call trace:
| fsl_lpspi_dma_transfer+0x260/0x340 [spi_fsl_lpspi]
| fsl_lpspi_transfer_one+0x198/0x448 [spi_fsl_lpspi]
| spi_transfer_one_message+0x49c/0x7c8
| __spi_pump_transfer_message+0x120/0x420
| __spi_sync+0x2c4/0x520
| spi_sync+0x34/0x60
| spidev_message+0x20c/0x378 [spidev]
| spidev_ioctl+0x398/0x750 [spidev]
[...]
Switch from devm_spi_register_controller() to spi_register_controller() in
fsl_lpspi_probe() and add the corresponding spi_unregister_controller() in
fsl_lpspi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_net: Fix UAF on dst_ops when IFF_XMIT_DST_RELEASE is cleared and napi_tx is false
A UAF issue occurs when the virtio_net driver is configured with napi_tx=N
and the device's IFF_XMIT_DST_RELEASE flag is cleared
(e.g., during the configuration of tc route filter rules).
When IFF_XMIT_DST_RELEASE is removed from the net_device, the network stack
expects the driver to hold the reference to skb->dst until the packet
is fully transmitted and freed. In virtio_net with napi_tx=N,
skbs may remain in the virtio transmit ring for an extended period.
If the network namespace is destroyed while these skbs are still pending,
the corresponding dst_ops structure has freed. When a subsequent packet
is transmitted, free_old_xmit() is triggered to clean up old skbs.
It then calls dst_release() on the skb associated with the stale dst_entry.
Since the dst_ops (referenced by the dst_entry) has already been freed,
a UAF kernel paging request occurs.
fix it by adds skb_dst_drop(skb) in start_xmit to explicitly release
the dst reference before the skb is queued in virtio_net.
Call Trace:
Unable to handle kernel paging request at virtual address ffff80007e150000
CPU: 2 UID: 0 PID: 6236 Comm: ping Kdump: loaded Not tainted 7.0.0-rc1+ #6 PREEMPT
...
percpu_counter_add_batch+0x3c/0x158 lib/percpu_counter.c:98 (P)
dst_release+0xe0/0x110 net/core/dst.c:177
skb_release_head_state+0xe8/0x108 net/core/skbuff.c:1177
sk_skb_reason_drop+0x54/0x2d8 net/core/skbuff.c:1255
dev_kfree_skb_any_reason+0x64/0x78 net/core/dev.c:3469
napi_consume_skb+0x1c4/0x3a0 net/core/skbuff.c:1527
__free_old_xmit+0x164/0x230 drivers/net/virtio_net.c:611 [virtio_net]
free_old_xmit drivers/net/virtio_net.c:1081 [virtio_net]
start_xmit+0x7c/0x530 drivers/net/virtio_net.c:3329 [virtio_net]
...
Reproduction Steps:
NETDEV="enp3s0"
config_qdisc_route_filter() {
tc qdisc del dev $NETDEV root
tc qdisc add dev $NETDEV root handle 1: prio
tc filter add dev $NETDEV parent 1:0 \
protocol ip prio 100 route to 100 flowid 1:1
ip route add 192.168.1.100/32 dev $NETDEV realm 100
}
test_ns() {
ip netns add testns
ip link set $NETDEV netns testns
ip netns exec testns ifconfig $NETDEV 10.0.32.46/24
ip netns exec testns ping -c 1 10.0.32.1
ip netns del testns
}
config_qdisc_route_filter
test_ns
sleep 2
test_ns |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: fix folio isn't locked in softleaf_to_folio()
On arm64 server, we found folio that get from migration entry isn't locked
in softleaf_to_folio(). This issue triggers when mTHP splitting and
zap_nonpresent_ptes() races, and the root cause is lack of memory barrier
in softleaf_to_folio(). The race is as follows:
CPU0 CPU1
deferred_split_scan() zap_nonpresent_ptes()
lock folio
split_folio()
unmap_folio()
change ptes to migration entries
__split_folio_to_order() softleaf_to_folio()
set flags(including PG_locked) for tail pages folio = pfn_folio(softleaf_to_pfn(entry))
smp_wmb() VM_WARN_ON_ONCE(!folio_test_locked(folio))
prep_compound_page() for tail pages
In __split_folio_to_order(), smp_wmb() guarantees page flags of tail pages
are visible before the tail page becomes non-compound. smp_wmb() should
be paired with smp_rmb() in softleaf_to_folio(), which is missed. As a
result, if zap_nonpresent_ptes() accesses migration entry that stores tail
pfn, softleaf_to_folio() may see the updated compound_head of tail page
before page->flags.
This issue will trigger VM_WARN_ON_ONCE() in pfn_swap_entry_folio()
because of the race between folio split and zap_nonpresent_ptes()
leading to a folio incorrectly undergoing modification without a folio
lock being held.
This is a BUG_ON() before commit 93976a20345b ("mm: eliminate further
swapops predicates"), which in merged in v6.19-rc1.
To fix it, add missing smp_rmb() if the softleaf entry is migration entry
in softleaf_to_folio() and softleaf_to_page().
[tujinjiang@huawei.com: update function name and comments] |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: convert inline data to extents when truncate exceeds inline size
Add a check in ext4_setattr() to convert files from inline data storage
to extent-based storage when truncate() grows the file size beyond the
inline capacity. This prevents the filesystem from entering an
inconsistent state where the inline data flag is set but the file size
exceeds what can be stored inline.
Without this fix, the following sequence causes a kernel BUG_ON():
1. Mount filesystem with inode that has inline flag set and small size
2. truncate(file, 50MB) - grows size but inline flag remains set
3. sendfile() attempts to write data
4. ext4_write_inline_data() hits BUG_ON(write_size > inline_capacity)
The crash occurs because ext4_write_inline_data() expects inline storage
to accommodate the write, but the actual inline capacity (~60 bytes for
i_block + ~96 bytes for xattrs) is far smaller than the file size and
write request.
The fix checks if the new size from setattr exceeds the inode's actual
inline capacity (EXT4_I(inode)->i_inline_size) and converts the file to
extent-based storage before proceeding with the size change.
This addresses the root cause by ensuring the inline data flag and file
size remain consistent during truncate operations. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: replace BUG_ON with proper error handling in ext4_read_inline_folio
Replace BUG_ON() with proper error handling when inline data size
exceeds PAGE_SIZE. This prevents kernel panic and allows the system to
continue running while properly reporting the filesystem corruption.
The error is logged via ext4_error_inode(), the buffer head is released
to prevent memory leak, and -EFSCORRUPTED is returned to indicate
filesystem corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: publish jinode after initialization
ext4_inode_attach_jinode() publishes ei->jinode to concurrent users.
It used to set ei->jinode before jbd2_journal_init_jbd_inode(),
allowing a reader to observe a non-NULL jinode with i_vfs_inode
still unset.
The fast commit flush path can then pass this jinode to
jbd2_wait_inode_data(), which dereferences i_vfs_inode->i_mapping and
may crash.
Below is the crash I observe:
```
BUG: unable to handle page fault for address: 000000010beb47f4
PGD 110e51067 P4D 110e51067 PUD 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 1 UID: 0 PID: 4850 Comm: fc_fsync_bench_ Not tainted 6.18.0-00764-g795a690c06a5 #1 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.17.0-2-2 04/01/2014
RIP: 0010:xas_find_marked+0x3d/0x2e0
Code: e0 03 48 83 f8 02 0f 84 f0 01 00 00 48 8b 47 08 48 89 c3 48 39 c6 0f 82 fd 01 00 00 48 85 c9 74 3d 48 83 f9 03 77 63 4c 8b 0f <49> 8b 71 08 48 c7 47 18 00 00 00 00 48 89 f1 83 e1 03 48 83 f9 02
RSP: 0018:ffffbbee806e7bf0 EFLAGS: 00010246
RAX: 000000000010beb4 RBX: 000000000010beb4 RCX: 0000000000000003
RDX: 0000000000000001 RSI: 0000002000300000 RDI: ffffbbee806e7c10
RBP: 0000000000000001 R08: 0000002000300000 R09: 000000010beb47ec
R10: ffff9ea494590090 R11: 0000000000000000 R12: 0000002000300000
R13: ffffbbee806e7c90 R14: ffff9ea494513788 R15: ffffbbee806e7c88
FS: 00007fc2f9e3e6c0(0000) GS:ffff9ea6b1444000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000010beb47f4 CR3: 0000000119ac5000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
filemap_get_folios_tag+0x87/0x2a0
__filemap_fdatawait_range+0x5f/0xd0
? srso_alias_return_thunk+0x5/0xfbef5
? __schedule+0x3e7/0x10c0
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? preempt_count_sub+0x5f/0x80
? srso_alias_return_thunk+0x5/0xfbef5
? cap_safe_nice+0x37/0x70
? srso_alias_return_thunk+0x5/0xfbef5
? preempt_count_sub+0x5f/0x80
? srso_alias_return_thunk+0x5/0xfbef5
filemap_fdatawait_range_keep_errors+0x12/0x40
ext4_fc_commit+0x697/0x8b0
? ext4_file_write_iter+0x64b/0x950
? srso_alias_return_thunk+0x5/0xfbef5
? preempt_count_sub+0x5f/0x80
? srso_alias_return_thunk+0x5/0xfbef5
? vfs_write+0x356/0x480
? srso_alias_return_thunk+0x5/0xfbef5
? preempt_count_sub+0x5f/0x80
ext4_sync_file+0xf7/0x370
do_fsync+0x3b/0x80
? syscall_trace_enter+0x108/0x1d0
__x64_sys_fdatasync+0x16/0x20
do_syscall_64+0x62/0x2c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
...
```
Fix this by initializing the jbd2_inode first.
Use smp_wmb() and WRITE_ONCE() to publish ei->jinode after
initialization. Readers use READ_ONCE() to fetch the pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: validate p_idx bounds in ext4_ext_correct_indexes
ext4_ext_correct_indexes() walks up the extent tree correcting
index entries when the first extent in a leaf is modified. Before
accessing path[k].p_idx->ei_block, there is no validation that
p_idx falls within the valid range of index entries for that
level.
If the on-disk extent header contains a corrupted or crafted
eh_entries value, p_idx can point past the end of the allocated
buffer, causing a slab-out-of-bounds read.
Fix this by validating path[k].p_idx against EXT_LAST_INDEX() at
both access sites: before the while loop and inside it. Return
-EFSCORRUPTED if the index pointer is out of range, consistent
with how other bounds violations are handled in the ext4 extent
tree code. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid infinite loops caused by residual data
On the mkdir/mknod path, when mapping logical blocks to physical blocks,
if inserting a new extent into the extent tree fails (in this example,
because the file system disabled the huge file feature when marking the
inode as dirty), ext4_ext_map_blocks() only calls ext4_free_blocks() to
reclaim the physical block without deleting the corresponding data in
the extent tree. This causes subsequent mkdir operations to reference
the previously reclaimed physical block number again, even though this
physical block is already being used by the xattr block. Therefore, a
situation arises where both the directory and xattr are using the same
buffer head block in memory simultaneously.
The above causes ext4_xattr_block_set() to enter an infinite loop about
"inserted" and cannot release the inode lock, ultimately leading to the
143s blocking problem mentioned in [1].
If the metadata is corrupted, then trying to remove some extent space
can do even more harm. Also in case EXT4_GET_BLOCKS_DELALLOC_RESERVE
was passed, remove space wrongly update quota information.
Jan Kara suggests distinguishing between two cases:
1) The error is ENOSPC or EDQUOT - in this case the filesystem is fully
consistent and we must maintain its consistency including all the
accounting. However these errors can happen only early before we've
inserted the extent into the extent tree. So current code works correctly
for this case.
2) Some other error - this means metadata is corrupted. We should strive to
do as few modifications as possible to limit damage. So I'd just skip
freeing of allocated blocks.
[1]
INFO: task syz.0.17:5995 blocked for more than 143 seconds.
Call Trace:
inode_lock_nested include/linux/fs.h:1073 [inline]
__start_dirop fs/namei.c:2923 [inline]
start_dirop fs/namei.c:2934 [inline] |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: reject mount if bigalloc with s_first_data_block != 0
bigalloc with s_first_data_block != 0 is not supported, reject mounting
it. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix use-after-free in update_super_work when racing with umount
Commit b98535d09179 ("ext4: fix bug_on in start_this_handle during umount
filesystem") moved ext4_unregister_sysfs() before flushing s_sb_upd_work
to prevent new error work from being queued via /proc/fs/ext4/xx/mb_groups
reads during unmount. However, this introduced a use-after-free because
update_super_work calls ext4_notify_error_sysfs() -> sysfs_notify() which
accesses the kobject's kernfs_node after it has been freed by kobject_del()
in ext4_unregister_sysfs():
update_super_work ext4_put_super
----------------- --------------
ext4_unregister_sysfs(sb)
kobject_del(&sbi->s_kobj)
__kobject_del()
sysfs_remove_dir()
kobj->sd = NULL
sysfs_put(sd)
kernfs_put() // RCU free
ext4_notify_error_sysfs(sbi)
sysfs_notify(&sbi->s_kobj)
kn = kobj->sd // stale pointer
kernfs_get(kn) // UAF on freed kernfs_node
ext4_journal_destroy()
flush_work(&sbi->s_sb_upd_work)
Instead of reordering the teardown sequence, fix this by making
ext4_notify_error_sysfs() detect that sysfs has already been torn down
by checking s_kobj.state_in_sysfs, and skipping the sysfs_notify() call
in that case. A dedicated mutex (s_error_notify_mutex) serializes
ext4_notify_error_sysfs() against kobject_del() in ext4_unregister_sysfs()
to prevent TOCTOU races where the kobject could be deleted between the
state_in_sysfs check and the sysfs_notify() call. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Fix memory leak when a wq is reset
idxd_wq_disable_cleanup() which is called from the reset path for a
workqueue, sets the wq type to NONE, which for other parts of the
driver mean that the wq is empty (all its resources were released).
Only set the wq type to NONE after its resources are released. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_log: fix uninitialized padding leak in NFULA_PAYLOAD
__build_packet_message() manually constructs the NFULA_PAYLOAD netlink
attribute using skb_put() and skb_copy_bits(), bypassing the standard
nla_reserve()/nla_put() helpers. While nla_total_size(data_len) bytes
are allocated (including NLA alignment padding), only data_len bytes
of actual packet data are copied. The trailing nla_padlen(data_len)
bytes (1-3 when data_len is not 4-byte aligned) are never initialized,
leaking stale heap contents to userspace via the NFLOG netlink socket.
Replace the manual attribute construction with nla_reserve(), which
handles the tailroom check, header setup, and padding zeroing via
__nla_reserve(). The subsequent skb_copy_bits() fills in the payload
data on top of the properly initialized attribute. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: fix use of uninitialized rtp_addr in process_sdp
process_sdp() declares union nf_inet_addr rtp_addr on the stack and
passes it to the nf_nat_sip sdp_session hook after walking the SDP
media descriptions. However rtp_addr is only initialized inside the
media loop when a recognized media type with a non-zero port is found.
If the SDP body contains no m= lines, only inactive media sections
(m=audio 0 ...) or only unrecognized media types, rtp_addr is never
assigned. Despite that, the function still calls hooks->sdp_session()
with &rtp_addr, causing nf_nat_sdp_session() to format the stale stack
value as an IP address and rewrite the SDP session owner and connection
lines with it.
With CONFIG_INIT_STACK_ALL_ZERO (default on most distributions) this
results in the session-level o= and c= addresses being rewritten to
0.0.0.0 for inactive SDP sessions. Without stack auto-init the
rewritten address is whatever happened to be on the stack.
Fix this by pre-initializing rtp_addr from the session-level connection
address (caddr) when available, and tracking via a have_rtp_addr flag
whether any valid address was established. Skip the sdp_session hook
entirely when no valid address exists. |
