| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: aspeed-vhub: cancel wake work on device removal
wake_work is armed from the gadget .wakeup callback to resume suspended
downstream ports, and it is never cancelled in ast_vhub_remove(), so a
work item queued before or during removal can run after devm has freed
vhub and its ports, a use-after-free.
Cancelling the work alone is not sufficient: usb_gadget_wakeup() takes
no lock and the unbind path never clears wakeup_en, so a remote-wakeup
request in flight on another CPU can re-arm the work after the cancel
and before vhub is freed.
ast_vhub_del_dev() already clears d->registered under vhub->lock before
unregistering the gadget. Refuse the wakeup in ast_vhub_udc_wakeup()
once d->registered is clear: the check and the schedule_work() are then
atomic against the unbind, so a wakeup that passed before the flag was
cleared is drained by the cancel_work_sync() after the del_dev loop,
and one that arrives later returns without arming. Also move INIT_WORK()
to the top of ast_vhub_probe(), since the probe error path reuses
ast_vhub_remove() and would otherwise cancel a never-initialized work
item.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix ACP MFD device leak on init failure
acp_hw_init() registers ACP child devices with mfd_add_devices() before
attaching them to the ACP power domain and initializing the hardware.
If attaching a child to the power domain fails, or if the ACP reset or
clock enable operation times out, the failure path frees only the
source cell, resource, and platform-data allocations. The child
platform devices already registered by mfd_add_devices() remain
registered and are never released.
Remove the children from the power domain and unregister the MFD
devices on failures that occur after mfd_add_devices() succeeds. Keep
mfd_add_devices() failures on the existing cleanup path since the MFD
core already rolls back partially registered children itself.
The issue was identified by a static analysis tool I developed and
confirmed by manual review.
(cherry picked from commit 63da68d6a2279ec945581c990c5a59a5ae8b5560) |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix race between perf_event_exit_task() and perf_pending_task()
A race condition exists between perf_event_exit_task() and
perf_pending_task() during begin_new_exec().
During begin_new_exec(), perf_event_exit_task() may be called, and the
PF_EXITING flag is not set on task. So perf_sigtrap() continues to execute
and triggers WARN_ON_ONCE(event->ctx->task != current).
Since both task exit and exec paths can call perf_event_exit_task() which
sets ctx->task to TASK_TOMBSTONE, fix this by explicitly checking if
event->ctx->task equals TASK_TOMBSTONE and dropping the redundant
PF_EXITING check. |
| Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network. |
| Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethtool: keep rtnl_lock for the ioctl self test
An offline self test that brings the interface down and back up with
netif_close() / netif_open() requires rtnl_lock for both. Since the
ethtool IOCTL path became rtnl-optional for ops-locked drivers, the
ETHTOOL_TEST ioctl runs holding only the netdev instance lock, so on an
ops-locked driver the self test now tears the device down without
rtnl_lock.
With lockdep this reproduces deterministically on every offline self
test on such a driver; note the sole lock held is the instance lock, not
rtnl:
WARNING: suspicious RCU usage
net/core/netpoll.c:207 suspicious rcu_dereference_protected() usage!
1 lock held by ethtool/107:
#0: (&dev->lock){+.+.}, at: dev_ethtool
Call Trace:
netpoll_poll_disable
__dev_close_many
netif_close_many
netif_close
fbnic_self_test
dev_ethtool_locked
dev_ethtool
dev_ioctl
sock_ioctl
__x64_sys_ioctl
Without lockdep the same condition trips ASSERT_RTNL() in
__dev_close_many() / __dev_open(); that check only samples the global
rtnl state, so it can be masked by a concurrent rtnl holder, but the
device is still being reconfigured without the lock it requires.
The ethtool self_test is a legacy ioctl-only command, so an ETHTOOL_TEST
case is only needed on the ioctl path. Add an opt-in bit for drivers whose
self test needs rtnl_lock and set it on the ops-locked drivers whose
offline self test tears the interface down and up:
- fbnic (ops-locked via queue_mgmt_ops): fbnic_self_test() offline path
uses netif_close() / netif_open().
- bnxt (ops-locked via queue_mgmt_ops): bnxt_self_test() offline path
goes through bnxt_close_nic() / bnxt_half_open_nic() /
bnxt_half_close_nic() / bnxt_open_nic(), which close and reopen the
device. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_queue: hold nfnl mutex in event notifier
We must serialize the release notifier and the config netlink function.
A concurrent thread can issue close() which can call the release function
while unrelated socket processes UNBIND request for same portid:
Oops: general protection fault, [..]
RIP: 0010:__instance_destroy+0x60/0x210 [nfnetlink_queue]
Call Trace:
nfqnl_recv_config+0x9b0/0xdc0 [nfnetlink_queue]
nfnetlink_rcv_msg+0x7c2/0xeb0
? __pfx_nfnetlink_rcv_msg+0x10/0x10
After this, parallel UNBIND and URELEASE events are impossible.
This change isn't nice, but its the shortest fix given instances
are not refcounted and the nfnetlink config callback drops the
rcu read lock early due to need for sleeping allocations. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: publish HW_DEAD after worker is done
flow_offload_work_del() sets NF_FLOW_HW_DEAD before the work handler
clears NF_FLOW_HW_PENDING. Once a flow is both HW_DYING and HW_DEAD, a
concurrent garbage collection pass can remove it and schedule it for RCU
freeing.
The offload worker holds neither an RCU read lock nor a reference to the
flow. If it is preempted after publishing HW_DEAD, the RCU callback can
free the flow before the worker resumes and clears HW_PENDING, resulting
in a use-after-free.
Move HW_DEAD publication to the common worker epilogue after the pending
bit is cleared, making it the final flow access by destroy work. Order all
preceding flow accesses before publishing the bit that allows garbage
collection to free the object. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Preserve packet pointer class displacement in regsafe()
regsafe() maps packet pointer IDs between states and checks that each
current register range is a subset of the corresponding explored
register range. It does not, however, preserve the displacement between
registers that share a packet pointer ID.
This is unsound because packet range is shared by ID. A bounds check on
one class member updates every member, and a later access can consume the
range through another member. Commit 022ac0750883 ("bpf: use reg->var_off
instead of reg->off for pointers") folded the fixed pointer offset into
r64 and removed the old off equality check, so two individually narrower
registers can prune even when their displacement has changed. The
explored path can then license an out-of-bounds packet access on the
pruned path.
Require matching range bases for packet pointers with an ID. Together
with the existing ID mapping, this preserves the displacement between
members of each packet-pointer class without adding per-ID state.
Packet pointers without an ID remain unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
eth: fbnic: Fix payload page pool error cleanup
The payload page pool pointer contains an error pointer when its
allocation fails. The cleanup path passes that error pointer to
page_pool_destroy() instead of destroying the header page pool. This
can dereference the error pointer and leave the header page pool
allocated.
Destroy the header page pool instead. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: amd_sfh: Validate PCI BAR size before mapping
The amd_sfh driver maps PCI BAR 2 using pcim_iomap_regions() and
subsequently accesses MMIO registers at offsets up to 0x10958 (e.g.,
AMD_P2C_MSG3 at 0x1068C). However, the driver never validates that the BAR
size is large enough to cover these accesses. If the driver is bound to a
device with a smaller BAR 2, this leads to an out-of-bounds memory access
and a page fault during the probe function.
For example, a page fault can occur when reading from privdata->mmio +
AMD_P2C_MSG3 in mp2_select_ops():
BUG: unable to handle page fault for address: ffffc9000390368c
PGD 100000067 P4D 100000067 PUD 1012c1067 PMD 105b64067 PTE 0
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:readl arch/x86/include/asm/io.h:59 [inline]
RIP: 0010:mp2_select_ops drivers/hid/amd-sfh-hid/amd_sfh_pcie.c:282
[inline]
RIP: 0010:amd_mp2_pci_probe+0x337/0x5f0
drivers/hid/amd-sfh-hid/amd_sfh_pcie.c:487
Call Trace:
<TASK>
local_pci_probe drivers/pci/pci-driver.c:332 [inline]
pci_call_probe drivers/pci/pci-driver.c:394 [inline]
__pci_device_probe drivers/pci/pci-driver.c:455 [inline]
pci_device_probe+0x431/0xc90 drivers/pci/pci-driver.c:489
Fix this by verifying that the length of BAR 2 is at least 128KB before
attempting to map it. Since the maximum accessed offset is 0x10958, and PCI
BAR sizes are powers of 2, any legitimate hardware will have a BAR size of
at least 128KB. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Require kernel access for text poke events
Perf events with exclude_kernel=1 can be opened without kernel perf
access. However, exclude_kernel does not suppress text-poke sideband
records. Every PERF_RECORD_TEXT_POKE is marked PERF_RECORD_MISC_KERNEL
and contains a raw kernel instruction address.
An unprivileged task can therefore open and mmap a task-local software
event with text_poke=1. Both opening a count-only tracepoint event and
configuring UDP GRO for ESP-in-UDP cause updates to inline static calls;
the observer receives the relocated addresses of the modified instructions.
For a known kernel image, any such address reveals the runtime kernel
text base despite KASLR.
Call perf_allow_kernel() whenever attr.text_poke is set, regardless of
exclude_kernel. Events that neither monitor kernel execution nor request
text-poke records retain their existing permissions. |
| Use after free in Windows Broadcast DVR User Service allows an authorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: health: max30102: fix NULL dereference in interrupt handler
The interrupt is requested in max30102_probe() and stays enabled
for the lifetime of the device, but indio_dev->active_scan_mask is only
valid while a buffer is enabled. When an interrupt arrives while no
buffer is enabled, the handler dereferences the NULL active_scan_mask:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
__bitmap_weight+0x64/0x98 (P)
max30102_interrupt_handler+0x48/0x160 [max30102]
Call max30102_fifo_count() at the top of the handler and return early
unless it reports a FIFO sample is ready. Because FIFO_RDY is the only
interrupt source enabled in max30102_chip_init(), an invocation of
max30102_interrupt_handler() without the FIFO_RDY interrupt status bit
set carries no data to read and can return before touching
active_scan_mask. A negative return from max30102_fifo_count()
indicates a failed interrupt status read and is treated the same way. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: serialize buffer teardown with mode claims
Buffer-mode claims hold mlock to guarantee that the device remains in
buffer mode until the claim is released. Normal buffer updates take
info_exist_lock followed by mlock in iio_update_buffers().
However, iio_device_unregister() disables and deactivates all buffers
without taking mlock. This can invalidate buffer state, including
active_scan_mask, while a buffer-mode claim is held.
Take mlock in iio_disable_all_buffers() so that unregister honors the
mode-claim lifetime guarantee. The info_exist_lock -> mlock ordering
matches iio_update_buffers(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: sun4i-gpadc-iio: clean up on thermal zone registration failure
If devm_thermal_of_zone_register() fails, probe returns without
unregistering the IIO map array or disabling runtime PM.
Jump to err_map to release them. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: pac1934: check ACPI label duplication
A label duplication failure currently reaches the terminating-byte
write. Release the ACPI result and abort before accessing the missing
label; earlier labels are managed by devres.
Detected by static analysis and reviewed with AI-assisted source auditing. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ade9000: handle Phase C dip events in IRQ1 handler
ADE9000_ST1_CROSSING_DEPTH is the exclusive upper bound for scanning the
STATUS1 event bits, so a value of 25 left out the highest event bit,
ADE9000_ST1_DIPC_BIT (bit 25). Phase C dip events were never reported.
Bump the value to 26 so bit 25 is scanned. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ade9000: fix NULL pointer dereference in clkout registration
ade9000_setup_clkout() passes NULL as the register address when
registering a divider clock. During clock registration, the common
clock framework calls clk_divider_recalc_rate(), which dereferences
the address through readl(). As a result, probing an ADE9000 configured
as a clock provider with an external input clock crashes.
CLKOUT passes CLKIN through without changing its rate. Register it as
a 1:1 fixed-factor clock, which does not require register access.
This change does not affect the configuration using the internal clock,
for which the driver does not register a clock provider. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Reject oversized XDomain properties responses
tb_xdp_properties_request() allocates room for 45 data dwords in its
252-byte response buffer. The XDomain length field is six bits wide,
however, and a malicious peer can set it to 63. After the fixed response
fields are subtracted, the driver treats this as 48 data dwords.
Commit 322e93448d90 ("thunderbolt: Clamp XDomain response data copy to
allocation size") only bounds the copy against data_len. If data_len is
at least 48, memcpy() reads 192 bytes from the 180-byte res->data array,
causing a 12-byte heap out-of-bounds read. Commit 4db2bd2ed478
("thunderbolt: Limit XDomain response copy to actual frame size") limits
the earlier copy but does not constrain this header-derived length.
Reject response data lengths that exceed the allocated source buffer
before copying them into the assembled property block. |
