| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize fragmented ISO packet queueing
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn->data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cw1200: fix TX padding OOB read leaking heap data to device
The TX path rounds the transfer size up to the bus alignment
(align_size(), up to 511 bytes for SDIO, 1 byte for SPI) but sends
the padded length straight from the frame buffer, which has no room
reserved for the padding. cw1200_data_write() therefore reads past
the end of the frame and the bus transfer carries those bytes to the
device. A bogus device can collect up to 511 bytes of kernel heap
data per TX frame.
The RX path does not have this problem: it allocates the skb with
the aligned length (alloc_len) before reading.
Compute the exact padding with the bus align_size() callback, make
sure queued TX frames have tailroom for it, and zero the padding
bytes before the transfer so nothing past the frame is exposed.
This is not expected to change driver behavior on most cases: frame
contents and transfer sizes are unchanged, only the content of the
padding bytes (previously undefined stale memory, now zero), which
the device never reads since the WSM header carries the real frame
length. The skb expansion can only fail under memory exhaustion,
in which case the frame is dropped like on the existing error paths
of cw1200_tx().
Discovered by Atuin - Automated Vulnerability Discovery Engine. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: keep paired old chanctx alive
An in-place replacement keeps reciprocal replace_ctx pointers between
the old WILL_BE_REPLACED chanctx and the new REPLACES_OTHER chanctx.
However, the early free paths only consider assigned and reserved link
users when deciding whether to free the old chanctx.
That lets the old chanctx be freed too early while the replacement
partner still points back to it, either when the last assigned link is
released or when that link successfully reassigns to another existing
context. Later unreserve and switch-finalization paths can then follow a
stale replace_ctx pointer.
Keep a paired old chanctx alive until the replacement pair has been torn
down. Apply the same check to both __ieee80211_link_release_channel()
and ieee80211_link_use_reserved_reassign(). If the replacement is later
abandoned, ieee80211_link_unreserve_chanctx() already tears down the
pairing before freeing the old chanctx once no users remain. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix driver deregistration order
USB serial driver modules register one driver for the USB bus and one or
more drivers for the ports on the USB serial bus.
When unloading a driver module, the USB driver must be deregistered
before the USB serial bus drivers so that I/O is stopped before
unbinding the ports to avoid use-after-free in completion handlers
accessing port data.
Note that the "new_id" attributes must first be removed to prevent new
ids from being added and triggering a probe of the USB driver after it
has been deregistered. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: gp2ap020a00f: drain irq_work after free_irq
The threaded IRQ handler queues data->work through irq_work_queue() so
the trigger is polled from a per-CPU context. free_irq() does not flush
an irq_work the handler already queued, so after gp2ap020a00f_remove()
returns that work may still run and call iio_trigger_poll() on data->trig,
which the devm cleanup has already freed, causing a use-after-free.
Add irq_work_sync(&data->work) after free_irq() in remove() and in the
probe error path, mirroring commit 78601726d4a5 ("iio: trigger: sysfs:
fix use-after-free on remove").
Found by an in-house static analysis tool, confirmed by manual review. |
| In the Linux kernel, the following vulnerability has been resolved:
bna: prevent IOC timer rearm during teardown
bna: prevent IOC timer rearm during teardown
bnad_pci_remove() and the probe disable_ioceth path call
timer_delete_sync() for ioc_timer, sem_timer and hb_timer, but not for
iocpf_timer. bnad_iocpf_timeout() then takes bnad->bna_lock after
free_netdev() has freed the struct bnad.
Deleting iocpf_timer last does not fix this. sem_timer and
iocpf_timer rearm each other: bnad_iocpf_sem_timeout() can arm
iocpf_timer, and bnad_iocpf_timeout() arms sem_timer from
bfa_ioc_hw_sem_get() when the semaphore is busy.
timer_delete_sync() only waits out its own callback.
bnad_ioceth_disable() can time out and leave that callback live.
Shut all four IOC timers down with timer_shutdown_sync() on both
paths, so a later mod_timer() is ignored.
This issue was identified during our ongoing static-analysis research
while reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/vaddr: avoid hw-driven pte updates during damon_hugetlb_mkold()
damon_hugetlb_mkold() reads the page table entry into a local variable,
unsets the accessed bit in the variable, and updates the page table entry
with the updated variable value. If hardware updates the same page table
entry in parallel, the hw updates could be lost. For example,
hardware-updated dirty bits might be lost.
Avoid the parallel updates by clearing the page table entry when reading
it together, using huge_ptep_get_and_clear(). If a parallel write to the
memory is made after the clearing, the hw will see the page table entry is
cleared, trigger page fault and wait until it is handled. The page fault
handling will wait for damon_hugetlb_mkold() due to the page table lock.
Because hugetlbfs is an in-memory file system and hugetlb pages cannot be
reclaimed, no critical issue is expected to my best knowledge. But
definitely this is a nasty bug that should be fixed sooner rather than
later.
The issue was discovered [1] by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: alps: unregister DualPoint Stick input device on remove
alps_input_configured() allocates a second input device ("DualPoint
Stick") with input_allocate_device() and registers it, but the
alps_driver struct has no .remove handler and input2 is not tracked in
hdev->inputs. The default remove path (hid_hw_stop -> hidinput_disconnect)
only iterates hdev->inputs, so input2 is never unregistered and leaks
on every device removal.
Add a .remove handler that stops the device first (preventing URB
callbacks from touching input2 during teardown) and then unregisters
input2. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Fix NULL pmu_ctx passed to pmu->sched_task()
perf_pmu_sched_task() returns early when cpuctx->task_ctx is set, and
cpc->task_epc is only non-NULL while a task context is scheduled in on
this CPU. __perf_pmu_sched_task() therefore always passes NULL:
Unable to handle kernel NULL pointer dereference at virtual address 00
pc : armv8pmu_sched_task+0x14/0x50
Call trace:
armv8pmu_sched_task+0x14/0x50 (P)
perf_pmu_sched_task+0xac/0x108
__perf_event_task_sched_out+0x6c/0xe0
Pass &cpc->epc instead, the CPU-wide context for this PMU, which the
function already dereferences a few lines up to find pmu.
armv8pmu_sched_task() is the only in-tree implementation that
dereferences the argument, and it only reads ->pmu, so the oops needs
BRBE, added in v6.17. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: close handle after create-context parsing failure
SMB2_open() accounts a successful CREATE response as a remote open before
parsing its create contexts. If smb2_parse_contexts() rejects malformed
context data, SMB2_open() returns without closing the handle, leaving the
server-side handle open and num_remote_opens elevated.
Close the handle after a post-CREATE context parsing failure so the error
path releases the remote resource and balances the open count. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: close completed creates on compound wait errors
compound_send_recv() waits for responses in order. If a later wait is
interrupted, or if a later MID fails during response synchronization, an
earlier CREATE may already have opened a remote handle. The earlier mid
is then released without invoking handle_cancelled_mid(), leaving the
remote handle open because no FID was copied to the caller.
Mark completed earlier mids as cancelled when a compound wait or MID
synchronization aborts. Keep their response buffers attached while the
MIDs are synchronized, and transfer them only after synchronization of
the processed responses, so the release path can inspect successful
CREATE responses and queue SMB2_close() after a later failure. Account for
a remote open only after the close work is allocated and before it is
queued, since the caller has not yet updated num_remote_opens. Mark the
create+close compound used by smb2_unlink() so it is not closed again.
Non-CREATE responses and compounds that already include a close keep their
existing behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Use memset_io() to clear QLAFX00 request ring slot
For QLAFX00 the request ring is ioremapped device I/O memory
(ha->iobase + req_que_off), not DMA-coherent RAM, which is why the rest
of the FX00 path accesses it through memcpy_toio() and the wrt_reg_*
helpers. __qla2x00_alloc_iocbs() however zeroed the producer slot with a
plain memset(). On architectures such as ARM64 a regular memset() may
emit unaligned or block-zeroing instructions (e.g. DC ZVA) that are
invalid on Device memory, leading to a synchronous external abort.
Use memset_io() to clear the slot for QLAFX00, matching the I/O
accessors used elsewhere on this ring. Other adapters keep the plain
memset() on their DMA-coherent rings. The zero-fill is retained for FX00
because its IOCB builders (e.g. qlafx00_fxdisc_iocb()) copy only part of
the entry and rely on the unused tail being pre-zeroed. |
| In the Linux kernel, the following vulnerability has been resolved:
vlan: require the MAC header to be present in __vlan_insert_inner_tag()
__vlan_insert_inner_tag() only guarantees head room via skb_cow_head(),
never that mac_len bytes of MAC header are present. Its ETH_HLEN
wrappers - __vlan_insert_tag() under skb_vlan_push(), and
vlan_insert_tag() under validate_xmit_vlan() on the generic transmit
path - therefore rewrite the first 16 bytes at skb->data: a 12-byte
memmove plus two 2-byte stores at +12 and +14. No caller supplies the
bound, while the pop helpers use skb_ensure_writable()/pskb_may_pull().
An IFF_TUN device has hard_header_len == 0, so packet_snd() accepts a
one-byte AF_PACKET/SOCK_RAW frame. The first vlan push only sets a
hwaccel tag; the next - clsact "action vlan push" or
bpf_skb_vlan_push() - enters the helper with skb->len still 1. The
head comes from skbuff_small_head without __GFP_ZERO, so each push
drags bytes from beyond skb->tail into the frame. After three the
one-byte send leaves as 13 bytes carrying 11 bytes of uninitialised
slab:
0000: 5a b3 62 12 80 88 ff ff 00 b3 62 12 81
`------------------------------'
only 0x5a was sent; the rest is slab, here the top 56 bits of a
linear-map address
Require the MAC header the helper rewrites to be present, so such a
frame is dropped rather than transmitted. |
| In the Linux kernel, the following vulnerability has been resolved:
xen/netfront: drop RX packets with a short Ethernet header
handle_incoming_queue() pulls pull_to bytes into the head before
calling eth_type_trans(). pull_to is the length of the first RX slot,
capped at RX_COPY_THRESHOLD, and that length comes from the backend.
Nothing checks it against ETH_HLEN.
If the first slot is shorter than ETH_HLEN and more slots follow, the
head ends up shorter than an Ethernet header while skb->len is longer,
and eth_type_trans() BUG()s in __skb_pull(). If the whole packet is
shorter than ETH_HLEN, eth_type_trans() reads the header past the end
of the data instead.
Pull at least ETH_HLEN, and drop the packet if that fails, which also
drops packets too short to hold an Ethernet header. This also checks
the return value of the pull, which was ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: preserve mremap address delta when skipping page tables
move_hugetlb_page_tables() optimizes mremap() by advancing to the last
entry in the page table when the source page table does not exist, either
initially or after unsharing a PMD table. The common loop increment then
steps to the first entry in the next page table.
However, the code advances both the source and destination addresses to
the last entries in their respective page tables, which is wrong. The
destination address must be advanced only by the same amount as the source
address.
If the source and destination offsets within their page tables differ, the
destination address can be advanced too far, causing follow-up issues.
Fix this by advancing the destination address by the source advance
distance.
With a reproducer, we were able to trigger a kernel panic on x86-64. With
this fix in place, we can no longer reproduce the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/erdma: Use IRQ-safe XArray helpers for QP and CQ tables
Locked QP and CQ lookups from EQ interrupts can deadlock with
create-path XArray updates. If an interrupt arrives while the create
path holds the plain xa_lock, the lookup spins forever trying to
acquire the same lock.
Use IRQ-safe XArray helpers for all QP and CQ create-path updates,
including the GSI QP store and error paths. Initialize both arrays with
XA_FLAGS_LOCK_IRQ so sleeping allocations preserve interrupt state. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix queuing tx_work after workqueue is drained
hci_send_acl(), hci_send_sco() and hci_send_iso() queue hdev->tx_work
unconditionally. They can run from the L2CAP/SCO/ISO socket send path
while hci_dev_close_sync() is draining hdev->workqueue (HCIDEVDOWN
racing with a socket write). Since that queue_work() is not chained
work from the tx_work worker itself, __queue_work() sees the queue
marked __WQ_DRAINING, warns "cannot queue %ps on wq %s", and drops
the work:
WARNING: CPU: 1 PID: 5985 at kernel/workqueue.c:2352 __queue_work
Call Trace:
queue_work_on
l2cap_chan_send
l2cap_sock_sendmsg
...
hci_dev_close_sync() already sets HCI_CMD_DRAIN_WORKQUEUE before
draining, but only hci_cmd_work() and handle_cmd_cnt_and_timer()
check it before queuing. Route the tx_work producers through the
same guard via a shared hci_sched_tx() helper. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Clamp implicit feedback packet count to URB capacity
data_ep_set_params() allocates each data URB for exactly u->packets
isochronous frames, so urb->iso_frame_desc[] has u->packets slots and
ctx->packets is the driver's only record of that limit. For an implicit
feedback sink, snd_usb_queue_pending_output_urbs() overwrites it with the
sync source's packet count, which is calculated independently from the
capture endpoint's parameters. When that count is larger,
prepare_playback_urb() and prepare_silent_urb() can write
iso_frame_desc[] past the allocation; their existing bounds limit payload
bytes, not the descriptor index.
The reproducer uses a high-speed UAC2 device declaring bInterval 1 for
implicit feedback capture (8 packets) and bInterval 4 for playback
(1 packet). On the first capture completion after the stream starts, it
accesses seven descriptors spanning 112 bytes beyond the one-packet URB:
BUG: KASAN: slab-out-of-bounds in prepare_playback_urb (sound/usb/pcm.c:1560)
Write of size 4 at addr ffff88801e696ad0 by task vhci_rx/178
prepare_playback_urb (sound/usb/pcm.c:1560)
prepare_outbound_urb (sound/usb/endpoint.c:340)
snd_usb_queue_pending_output_urbs (sound/usb/endpoint.c:501)
snd_complete_urb (sound/usb/endpoint.c:1834)
__usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1657)
usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1741)
vhci_rx_loop (drivers/usb/usbip/vhci_rx.c:107)
kthread (kernel/kthread.c:436)
The buggy address belongs to the object at ffff88801e696a00
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 0 bytes to the right of
allocated 208-byte region [ffff88801e696a00, ffff88801e696ad0)
Record the allocated packet count per endpoint and clamp both the adopted
count and the packet-size copy to it. Fold the Format Type II delimiter
into urb_packs before the allocation loop so the recorded limit matches
every URB. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: take commit root semaphore when iterating in mark_block_group_to_copy()
mark_block_group_to_copy() iterates over the commit root with
skip_locking=true. A concurrent transaction commit can swap and free
the commit root during iteration, causing use-after-free when
accessing extent buffers.
Fix it by using path->need_commit_sem to protect the commit root search. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pwm-fan) Stop RPM timer before freeing tach data
sample_timer() rearms the RPM timer and accesses the devm-managed
ctx->tachs and ctx->pulses_per_revolution arrays. The cleanup action
which stops the timer is registered before those arrays are allocated.
Since devres releases entries in reverse order, driver detach can free
the arrays before pwm_fan_cleanup() shuts down the timer. A timer expiry
in that window accesses the freed tach data.
With a KASAN kernel, a test-only kprobe delayed entry to
pwm_fan_cleanup() while normal sysfs unbind ran. Each of three runs
reported three four-byte reads and two four-byte writes in sample_timer()
after its backing devm allocations had been freed. The helper did not
invoke the timer callback, cleanup actions or free functions.
With the fix, three matching unbind runs completed without KASAN, BUG,
WARNING, Oops or panic. Instrumentation confirmed that timer retirement
completed before the first timer backing allocation was released.
Split timer retirement from the power cleanup and register its devres
action after the timer backing data and IRQ actions are installed. This
preserves the early power rollback action while ensuring the timer is
retired before its backing data is released. Use timer_shutdown_sync()
because the callback can rearm itself. |
