| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: wwan: mhi_wwan_mbim: guard against a cyclic NDP chain
The NDP traversal in mhi_mbim_rx() only stops when wNextNdpIndex is
zero. Nothing requires the offsets to advance, so a modem that
points an NDP at itself, or at an earlier NDP, keeps the loop
spinning forever on one CPU.
Break out when the next NDP offset is not larger than the current
one.
Verified in a QEMU guest with a fault injector feeding the driver's
receive callback an NTB whose single NDP points at itself: the
unpatched driver spins in mhi_mbim_rx() with one CPU pinned at 100%
and the thread never returns. With this check the loop terminates
within one iteration.
Changes in v2: move the non-increasing check to the wNextNdpIndex
retrieval site, as suggested by Loic Poulain, instead of tracking
the previous offset in a separate variable. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: rt712-sdca-dmic: fix uninitialized stream_config->type
stream_config is not initialized before being passed to
sdw_stream_add_slave(). The type field may contain garbage and is
later copied to stream->type by sdw_config_stream().
Zero-initialize stream_config so type defaults to SDW_STREAM_PCM.
While at it, use snd_sdw_params_to_config() helper instead of
open-coding the same logic. |
| In the Linux kernel, the following vulnerability has been resolved:
net: psp: avoid conflicts with skb->decrypted and sk_validate_xmit_skb()
PSP conflicts with TLS ULP in its usage of both skb->decrypted and
sk->sk_validate_xmit_skb().
Make PSP mutually exclusive with TLS ULP, the only other user of either
of these. As other users of skb->decrypted come along, they can be added
to sk_has_decrypt_user(). It would make sense to also assert that
sk->sk_validate_xmit_skb() is also NULL in both of these setup paths for
similar future proofing, but the PSP listener/sk_clone() path is still
broken and it could be seen as a regression to not allow rx assoc to run
on a child of a listener socket with PSP tx assoc state.
Include all TCP ULPs in the sk_has_decrypt_user() check, even though TLS
is the only one that conflicts with PSP via the decrypted bit. This is
intentional because PSP was not designed to be used with ULPs. It is
best to close off surface area that may make bugs reachable, until
someone wishes to design and test an actual user of PSP with ULPs. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: spi: reset bytes_xfered before retrying CRC failures
mmc_spi_data_do() updates data->bytes_xfered after each block has been
transferred successfully. If a later block in the same data request
fails with a CRC error, data->bytes_xfered may therefore contain the
number of bytes completed before the failing block.
mmc_spi_request() has a private recovery path for such CRC failures. It
sends STOP_TRANSMISSION, clears data->error and jumps back to
crc_recover to issue the same command and data request again. However,
it does not clear data->bytes_xfered before the retry.
If the retry succeeds, the request is completed with the bytes from the
failed attempt still included in data->bytes_xfered. For a multi-block
request this can make the completed request report more bytes than were
transferred by the successful retry, and can even exceed the request size
when most blocks completed before the CRC error.
This is most likely to be observed on MMC-over-SPI systems where long
multi-block transfers occasionally hit a data CRC error but the
mmc_spi-internal retry succeeds. The data itself is retried, but the
completion accounting is not.
Clear data->bytes_xfered together with data->error before repeating the
request so the final completion reports only the bytes transferred by the
successful attempt. |
| In the Linux kernel, the following vulnerability has been resolved:
mm, swap: fix SWAP_USAGE_OFFLIST_BIT collision with real usage count
SWAP_USAGE_OFFLIST_BIT is embedded in the si->inuse_pages usage counter,
and is meant to sit above any value that counter can reach. However, it
is defined from BITS_PER_TYPE(atomic_t), so it is bit 30. On a system
with 4 KiB pages the flag collides with the usage count once that count
reaches 4 TiB.
swap_usage_in_pages() masks bit 30 out, so whenever the real count has
that bit set, every caller of it reads 4 TiB low:
* /proc/swaps understates Used by 4 TiB.
* A raw count of exactly 2^30 masks to zero, so try_to_unuse() takes its
"if (!swap_usage_in_pages(si)) goto success;" early exit and swapoff
tears the device down while pages are still swapped out. Nothing in
the rest of swapoff aborts the teardown, so those pages are lost.
Independently of swapoff, the collision also corrupts the counter and the
plist. On a device in normal use, a free that leaves bit 30 set in the
count makes swap_usage_sub() see the flag where there is only count, and
call add_to_avail_list(). It clears the bit with
fetch_and(~SWAP_USAGE_OFFLIST_BIT), leaving the stored count 4 TiB below
the real one, and calls plist_add() on a device that is already listed,
tripping the WARN_ON(!plist_node_empty(node)) in plist_add() and linking
the node a second time.
Change the definition of SWAP_USAGE_OFFLIST_BIT to be based on
atomic_long_t instead. Note that the usage counter field itself is of
this same type, so it is still a valid bit. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libahci: clear PxCLBU and PxFBU for AHCI_HFLAG_32BIT_ONLY
A user reported that commit 105c42566a55 ("ata: ahci: force 32-bit DMA for
JMicron JMB582/JMB585") made the JMicron JMB585 unusable on his board.
The failure is seen as soon as the ahci driver is probed, and booting with
iommu=off does not solve the problem.
Looking at the AHCI specification, PxCLBU and PxFBU are both read only '0'
for HBAs that do not support 64-bit addressing.
For HBAs that do support 64-bit addressing, the registers are read write,
with a reset value that is Implementation Specific.
When using the AHCI_HFLAG_32BIT_ONLY flag, the HBA does support 64-bit
addressing, and a 32-bit DMA mask is set by simply clearing HOST_CAP_64.
Thus, in this case, we need to explicitly clear the registers to 0. |
| In the Linux kernel, the following vulnerability has been resolved:
9p: Fix v9fs_issue_write() to update i_size and remote_i_size
Fix v9fs_issue_write() to update i_size and remote_i_size to the new size
of the server file if we made it larger, using the start fpos and the count
returned by p9_client_write() to calculate the new minimum file size.
This assumes that if the 9P server makes a short write (say it hits
ENOSPC), a reduced count is returned. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_nat: fully initialise new_addr in netmap setup
nft_nat_setup_netmap() builds the mapped address in an on-stack
union nf_inet_addr. For an IPv4 mapping it writes only the 4-byte .ip
member and the loop runs a single 32-bit iteration, but it then copies
the whole 16-byte union into range->min_addr and range->max_addr, so the
upper 12 bytes reach nf_nat_setup_info() uninitialised.
KMSAN reports an uninit-value in nf_nat_setup_info() reached from
nft_nat_eval(). The IPv6 path fills all 16 bytes and is not affected.
Zero-initialise new_addr. |
| In sshd in OpenSSH before 10.6, GSSAPIAuthentication authentication state can incorrectly be persisted across authentication attempts. |
| Newell Brands DYMO ID 1.5.1.71 resolves its plugin Modules directory relative to the process working directory. An attacker could store a job file alongside malicious modules / DLL that sets the process working directory to the job file's folder when a victim clicks on the file, resulting in code execution at the victim's privilege level. Fixed in 1.6.0. |
| In the Linux kernel, the following vulnerability has been resolved:
seg6: set IPSKB_L3SLAVE from IP6SKB_L3SLAVE on IPIP decapsulation
When an SRv6 packet arrives on an interface enslaved to a VRF,
vrf_ip6_rcv() sets IP6SKB_L3SLAVE in IP6CB, but decap_and_validate()
has never set IPSKB_L3SLAVE in IPCB. The bit stayed clear in the
common case, and with CONFIG_IPV6_MIP6 the leftover frag_max_size of
a reassembled outer packet could even set it, with no VRF involved.
Commit 44930446dde4 ("ipv6: seg6: clear IPv4 control block on IPIP
decapsulation") then made the unreliable bit reliably clear.
The effect of the missing flag is visible with End.DX4 when a
delivery to a local address of the node reaches the socket lookup.
For example, a UDP socket bound to the enslaved ingress interface
does not receive any of the decapsulated packets, while an unbound
socket outside the VRF does.
This contradicts Documentation/networking/vrf.rst: by default the
scope of an unbound UDP or TCP socket is limited to the default VRF.
Set IPSKB_L3SLAVE for IPv4 in decap_and_validate(), which already does
the same for IPv6. The socket lookup then matches the decapsulated
packet like any other packet received on that enslaved interface. Such
a packet matches an unbound UDP or TCP socket only when
udp_l3mdev_accept or tcp_l3mdev_accept is set. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: don't start a ROC while scanning
The ROC work can be pending when a scan starts (which requires
ROC list to be empty, but that's possible), and then a new ROC
can be added to the list and the work will pick it up.
Avoid starting that ROC if a scan made it between things, as
otherwise we'll hit a warning later:
WARNING: net/mac80211/offchannel.c:404 at ieee80211_start_next_roc+0x256/0x2d0
Workqueue: events_unbound cfg80211_wiphy_work
Call Trace:
__ieee80211_scan_completed+0x4fd/0xe40 net/mac80211/scan.c:537
ieee80211_scan_work+0x472/0x1ff0 net/mac80211/scan.c:1193
cfg80211_wiphy_work+0x410/0x570 net/wireless/core.c:513 |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: Fix device kref underflow in dma_chan_put()
dma_chan_get() takes chan->device->ref only on the slow path:
/* no kref on fast path */
if (chan->client_count) {
__module_get(owner);
chan->client_count++;
return 0;
}
if (!try_module_get(owner))
return -ENODEV;
if (!dma_device_get(chan->device)) { // calls kref_get_unless_zero()
dma_chan_put() drops the ref unconditionally, so every fast-path
get/put pair drops one extra device reference.
The bug fires when two conditions hold together: a non-private
provider has a persistent client holding chan->client_count > 0
and another client cycles dmaengine_get()/dmaengine_put().
When the kref hits zero, the subsequent dma_find_channel() returns
NULL even though the provider module is still loaded.
Fix this by dropping device->ref only on the last put, matching the
single slow-path get. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: set up the TX info early to fix failure paths
The previous commit 2c51457d930f ("wifi: mac80211: free ack status
frame on TX header build failure") cleaned up the leak, but still
left the code a bit messy and the failed SKB didn't get reported
to userspace.
Fix this up by initialising skb->cb[] earlier, which allows using
ieee80211_free_txskb() and therefore reports it for the failure
in ieee80211_build_hdr(), and unifies the ieee80211_skb_resize()
failure path with it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: add HE 6 GHz capability in the scan elems len
The HE 6 GHz Band Capability element is in the probe request for
every band if 6 GHz is supported, so add the size to scan_ies_len.
Otherwise, building probe request elements can fail, triggering the
WARN_ON in __ieee80211_start_scan(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: only group hidden BSSes with beacon entries
When a probe response for an unknown BSS comes in, __cfg80211_bss_update()
looks for an existing entry with the same BSSID and a hidden (zero-length
or NUL-filled) SSID, and if it finds one it groups them, using the beacon
IEs from the existing entry.
But that could find another entry without a beacon, if it was also from a
probe response (with SSID), so there's a group without beacon elements.
If a beacon with a hidden SSID for that BSSID arrives later,
cfg80211_combine_bsses() goes looking for the probe response entries that
belong to it - i.e. entries with the same BSSID and channel that have no
beacon IEs - and finds those two. They are already grouped with each
other, so it hits its
WARN_ON_ONCE(bss->pub.hidden_beacon_bss)
WARN_ON_ONCE(!list_empty(&bss->hidden_list))
which are there because an entry without beacon elements is not supposed
to be part of a group yet.
Only combine entries when a beacon was already received, ones that are
kept separate will be combined when a beacon arrives. |
| BuildKit may be tricked into performing file actions with special file inodes where regular files are expected. Special files may block operations or, on rootful workers, allow unintended host device access. |
| Pexip Infinity before 38.2, plus 39.0, 39.1, and 40.0, is affected by improper input validation within an internal Pexip Infinity service that allows an attacker with local access to escalate privileges to root. Exploitation requires an attacker to be able to run arbitrary code on a node by either achieving remote code execution via some other vulnerability or having administrative access to the operating system. |
| Nezha Dashboard from 1.8.0 before 2.3.13 contains an improper locking vulnerability where a non-deferred mutex unlock leaks on a nil-map panic path. Any authenticated non-admin member can issue four notification API calls to permanently deadlock the alerting subsystem, then exhaust memory with blocking requests. |
| Improper initialization in an ASUS certain motherboard allows an physically proximate user to read or write arbitrary memory by inserting a specially crafted device.
Refer to the '
Security Update for Multiple ASUS Motherboards ' section on the ASUS Security Advisory for more information. |
