| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix use-after-free of sbi in f2fs_compress_write_end_io()
In f2fs_compress_write_end_io(), dec_page_count(sbi, type) can bring
the F2FS_WB_CP_DATA counter to zero, unblocking
f2fs_wait_on_all_pages() in f2fs_put_super() on a concurrent unmount
CPU. The unmount path then proceeds to call
f2fs_destroy_page_array_cache(sbi), which destroys
sbi->page_array_slab via kmem_cache_destroy(), and eventually
kfree(sbi). Meanwhile, the bio completion callback is still executing:
when it reaches page_array_free(sbi, ...), it dereferences
sbi->page_array_slab — a destroyed slab cache — to call
kmem_cache_free(), causing a use-after-free.
This is the same class of bug as CVE-2026-23234 (which fixed the
equivalent race in f2fs_write_end_io() in data.c), but in the
compressed writeback completion path that was not covered by that fix.
Fix this by moving dec_page_count() to after page_array_free(), so
that all sbi accesses complete before the counter decrement that can
unblock unmount. For non-last folios (where atomic_dec_return on
cic->pending_pages is nonzero), dec_page_count is called immediately
before returning — page_array_free is not reached on this path, so
there is no post-decrement sbi access. For the last folio,
page_array_free runs while the F2FS_WB_CP_DATA counter is still
nonzero (this folio has not yet decremented it), keeping sbi alive,
and dec_page_count runs as the final operation. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/kasan: fix double free for kasan pXds
kasan_free_pxd() assumes the page table is always struct page aligned.
But that's not always the case for all architectures. E.g. In case of
powerpc with 64K pagesize, PUD table (of size 4096) comes from slab cache
named pgtable-2^9. Hence instead of page_to_virt(pxd_page()) let's just
directly pass the start of the pxd table which is passed as the 1st
argument.
This fixes the below double free kasan issue seen with PMEM:
radix-mmu: Mapped 0x0000047d10000000-0x0000047f90000000 with 2.00 MiB pages
==================================================================
BUG: KASAN: double-free in kasan_remove_zero_shadow+0x9c4/0xa20
Free of addr c0000003c38e0000 by task ndctl/2164
CPU: 34 UID: 0 PID: 2164 Comm: ndctl Not tainted 6.19.0-rc1-00048-gea1013c15392 #157 VOLUNTARY
Hardware name: IBM,9080-HEX POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_012) hv:phyp pSeries
Call Trace:
dump_stack_lvl+0x88/0xc4 (unreliable)
print_report+0x214/0x63c
kasan_report_invalid_free+0xe4/0x110
check_slab_allocation+0x100/0x150
kmem_cache_free+0x128/0x6e0
kasan_remove_zero_shadow+0x9c4/0xa20
memunmap_pages+0x2b8/0x5c0
devm_action_release+0x54/0x70
release_nodes+0xc8/0x1a0
devres_release_all+0xe0/0x140
device_unbind_cleanup+0x30/0x120
device_release_driver_internal+0x3e4/0x450
unbind_store+0xfc/0x110
drv_attr_store+0x78/0xb0
sysfs_kf_write+0x114/0x140
kernfs_fop_write_iter+0x264/0x3f0
vfs_write+0x3bc/0x7d0
ksys_write+0xa4/0x190
system_call_exception+0x190/0x480
system_call_vectored_common+0x15c/0x2ec
---- interrupt: 3000 at 0x7fff93b3d3f4
NIP: 00007fff93b3d3f4 LR: 00007fff93b3d3f4 CTR: 0000000000000000
REGS: c0000003f1b07e80 TRAP: 3000 Not tainted (6.19.0-rc1-00048-gea1013c15392)
MSR: 800000000280f033 <SF,VEC,VSX,EE,PR,FP,ME,IR,DR,RI,LE> CR: 48888208 XER: 00000000
<...>
NIP [00007fff93b3d3f4] 0x7fff93b3d3f4
LR [00007fff93b3d3f4] 0x7fff93b3d3f4
---- interrupt: 3000
The buggy address belongs to the object at c0000003c38e0000
which belongs to the cache pgtable-2^9 of size 4096
The buggy address is located 0 bytes inside of
4096-byte region [c0000003c38e0000, c0000003c38e1000)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x3c38c
head: order:2 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
memcg:c0000003bfd63e01
flags: 0x63ffff800000040(head|node=6|zone=0|lastcpupid=0x7ffff)
page_type: f5(slab)
raw: 063ffff800000040 c000000140058980 5deadbeef0000122 0000000000000000
raw: 0000000000000000 0000000080200020 00000000f5000000 c0000003bfd63e01
head: 063ffff800000040 c000000140058980 5deadbeef0000122 0000000000000000
head: 0000000000000000 0000000080200020 00000000f5000000 c0000003bfd63e01
head: 063ffff800000002 c00c000000f0e301 00000000ffffffff 00000000ffffffff
head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000004
page dumped because: kasan: bad access detected
[ 138.953636] [ T2164] Memory state around the buggy address:
[ 138.953643] [ T2164] c0000003c38dff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 138.953652] [ T2164] c0000003c38dff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 138.953661] [ T2164] >c0000003c38e0000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 138.953669] [ T2164] ^
[ 138.953675] [ T2164] c0000003c38e0080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 138.953684] [ T2164] c0000003c38e0100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 138.953692] [ T2164] ==================================================================
[ 138.953701] [ T2164] Disabling lock debugging due to kernel taint |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix use-after-free in ocfs2_fault() when VM_FAULT_RETRY
filemap_fault() may drop the mmap_lock before returning VM_FAULT_RETRY,
as documented in mm/filemap.c:
"If our return value has VM_FAULT_RETRY set, it's because the mmap_lock
may be dropped before doing I/O or by lock_folio_maybe_drop_mmap()."
When this happens, a concurrent munmap() can call remove_vma() and free
the vm_area_struct via RCU. The saved 'vma' pointer in ocfs2_fault() then
becomes a dangling pointer, and the subsequent trace_ocfs2_fault() call
dereferences it -- a use-after-free.
Fix this by saving ip_blkno as a plain integer before calling
filemap_fault(), and removing vma from the trace event. Since
ip_blkno is copied by value before the lock can be dropped, it
remains valid regardless of what happens to the vma or inode
afterward. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6apm: move component registration to unmanaged version
q6apm component registers dais dynamically from ASoC toplology, which
are allocated using device managed version apis. Allocating both
component and dynamic dais using managed version could lead to incorrect
free ordering, dai will be freed while component still holding references
to it.
Fix this issue by moving component to unmanged version so
that the dai pointers are only freeded after the component is removed.
==================================================================
BUG: KASAN: slab-use-after-free in snd_soc_del_component_unlocked+0x3d4/0x400 [snd_soc_core]
Read of size 8 at addr ffff00084493a6e8 by task kworker/u48:0/3426
Tainted: [W]=WARN
Hardware name: LENOVO 21N2ZC5PUS/21N2ZC5PUS, BIOS N42ET57W (1.31 ) 08/08/2024
Workqueue: pdr_notifier_wq pdr_notifier_work [pdr_interface]
Call trace:
show_stack+0x28/0x7c (C)
dump_stack_lvl+0x60/0x80
print_report+0x160/0x4b4
kasan_report+0xac/0xfc
__asan_report_load8_noabort+0x20/0x34
snd_soc_del_component_unlocked+0x3d4/0x400 [snd_soc_core]
snd_soc_unregister_component_by_driver+0x50/0x88 [snd_soc_core]
devm_component_release+0x30/0x5c [snd_soc_core]
devres_release_all+0x13c/0x210
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x350/0x468
device_release_driver+0x18/0x30
bus_remove_device+0x1a0/0x35c
device_del+0x314/0x7f0
device_unregister+0x20/0xbc
apr_remove_device+0x5c/0x7c [apr]
device_for_each_child+0xd8/0x160
apr_pd_status+0x7c/0xa8 [apr]
pdr_notifier_work+0x114/0x240 [pdr_interface]
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20
Allocated by task 77:
kasan_save_stack+0x40/0x68
kasan_save_track+0x20/0x40
kasan_save_alloc_info+0x44/0x58
__kasan_kmalloc+0xbc/0xdc
__kmalloc_node_track_caller_noprof+0x1f4/0x620
devm_kmalloc+0x7c/0x1c8
snd_soc_register_dai+0x50/0x4f0 [snd_soc_core]
soc_tplg_pcm_elems_load+0x55c/0x1eb8 [snd_soc_core]
snd_soc_tplg_component_load+0x4f8/0xb60 [snd_soc_core]
audioreach_tplg_init+0x124/0x1fc [snd_q6apm]
q6apm_audio_probe+0x10/0x1c [snd_q6apm]
snd_soc_component_probe+0x5c/0x118 [snd_soc_core]
soc_probe_component+0x44c/0xaf0 [snd_soc_core]
snd_soc_bind_card+0xad0/0x2370 [snd_soc_core]
snd_soc_register_card+0x3b0/0x4c0 [snd_soc_core]
devm_snd_soc_register_card+0x50/0xc8 [snd_soc_core]
x1e80100_platform_probe+0x208/0x368 [snd_soc_x1e80100]
platform_probe+0xc0/0x188
really_probe+0x188/0x804
__driver_probe_device+0x158/0x358
driver_probe_device+0x60/0x190
__device_attach_driver+0x16c/0x2a8
bus_for_each_drv+0x100/0x194
__device_attach+0x174/0x380
device_initial_probe+0x14/0x20
bus_probe_device+0x124/0x154
deferred_probe_work_func+0x140/0x220
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20
Freed by task 3426:
kasan_save_stack+0x40/0x68
kasan_save_track+0x20/0x40
__kasan_save_free_info+0x4c/0x80
__kasan_slab_free+0x78/0xa0
kfree+0x100/0x4a4
devres_release_all+0x144/0x210
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x350/0x468
device_release_driver+0x18/0x30
bus_remove_device+0x1a0/0x35c
device_del+0x314/0x7f0
device_unregister+0x20/0xbc
apr_remove_device+0x5c/0x7c [apr]
device_for_each_child+0xd8/0x160
apr_pd_status+0x7c/0xa8 [apr]
pdr_notifier_work+0x114/0x240 [pdr_interface]
process_one_work+0x500/0xb70
worker_thread+0x630/0xfb0
kthread+0x370/0x6c0
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: 6fire: fix use-after-free on disconnect
In usb6fire_chip_abort(), the chip struct is allocated as the card's
private data (via snd_card_new with sizeof(struct sfire_chip)). When
snd_card_free_when_closed() is called and no file handles are open, the
card and embedded chip are freed synchronously. The subsequent
chip->card = NULL write then hits freed slab memory.
Call trace:
usb6fire_chip_abort sound/usb/6fire/chip.c:59 [inline]
usb6fire_chip_disconnect+0x348/0x358 sound/usb/6fire/chip.c:182
usb_unbind_interface+0x1a8/0x88c drivers/usb/core/driver.c:458
...
hub_event+0x1a04/0x4518 drivers/usb/core/hub.c:5953
Fix by moving the card lifecycle out of usb6fire_chip_abort() and into
usb6fire_chip_disconnect(). The card pointer is saved in a local
before any teardown, snd_card_disconnect() is called first to prevent
new opens, URBs are aborted while chip is still valid, and
snd_card_free_when_closed() is called last so chip is never accessed
after the card may be freed. |
| In the Linux kernel, the following vulnerability has been resolved:
media: as102: fix to not free memory after the device is registered in as102_usb_probe()
In as102_usb driver, the following race condition occurs:
```
CPU0 CPU1
as102_usb_probe()
kzalloc(); // alloc as102_dev_t
....
usb_register_dev();
fd = sys_open("/path/to/dev"); // open as102 fd
....
usb_deregister_dev();
....
kfree(); // free as102_dev_t
....
sys_close(fd);
as102_release() // UAF!!
as102_usb_release()
kfree(); // DFB!!
```
When a USB character device registered with usb_register_dev() is later
unregistered (via usb_deregister_dev() or disconnect), the device node is
removed so new open() calls fail. However, file descriptors that are
already open do not go away immediately: they remain valid until the last
reference is dropped and the driver's .release() is invoked.
In as102, as102_usb_probe() calls usb_register_dev() and then, on an
error path, does usb_deregister_dev() and frees as102_dev_t right away.
If userspace raced a successful open() before the deregistration, that
open FD will later hit as102_release() --> as102_usb_release() and access
or free as102_dev_t again, occur a race to use-after-free and
double-free vuln.
The fix is to never kfree(as102_dev_t) directly once usb_register_dev()
has succeeded. After deregistration, defer freeing memory to .release().
In other words, let release() perform the last kfree when the final open
FD is closed. |
| In the Linux kernel, the following vulnerability has been resolved:
media: hackrf: fix to not free memory after the device is registered in hackrf_probe()
In hackrf driver, the following race condition occurs:
```
CPU0 CPU1
hackrf_probe()
kzalloc(); // alloc hackrf_dev
....
v4l2_device_register();
....
fd = sys_open("/path/to/dev"); // open hackrf fd
....
v4l2_device_unregister();
....
kfree(); // free hackrf_dev
....
sys_ioctl(fd, ...);
v4l2_ioctl();
video_is_registered() // UAF!!
....
sys_close(fd);
v4l2_release() // UAF!!
hackrf_video_release()
kfree(); // DFB!!
```
When a V4L2 or video device is unregistered, the device node is removed so
new open() calls are blocked.
However, file descriptors that are already open-and any in-flight I/O-do
not terminate immediately; they remain valid until the last reference is
dropped and the driver's release() is invoked.
Therefore, freeing device memory on the error path after hackrf_probe()
has registered dev it will lead to a race to use-after-free vuln, since
those already-open handles haven't been released yet.
And since release() free memory too, race to use-after-free and
double-free vuln occur.
To prevent this, if device is registered from probe(), it should be
modified to free memory only through release() rather than calling
kfree() directly. |
| In the Linux kernel, the following vulnerability has been resolved:
driver core: platform: use generic driver_override infrastructure
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1] |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: compress: fix UAF of f2fs_inode_info in f2fs_free_dic
The decompress_io_ctx may be released asynchronously after
I/O completion. If this file is deleted immediately after read,
and the kworker of processing post_read_wq has not been executed yet
due to high workloads, It is possible that the inode(f2fs_inode_info)
is evicted and freed before it is used f2fs_free_dic.
The UAF case as below:
Thread A Thread B
- f2fs_decompress_end_io
- f2fs_put_dic
- queue_work
add free_dic work to post_read_wq
- do_unlink
- iput
- evict
- call_rcu
This file is deleted after read.
Thread C kworker to process post_read_wq
- rcu_do_batch
- f2fs_free_inode
- kmem_cache_free
inode is freed by rcu
- process_scheduled_works
- f2fs_late_free_dic
- f2fs_free_dic
- f2fs_release_decomp_mem
read (dic->inode)->i_compress_algorithm
This patch store compress_algorithm and sbi in dic to avoid inode UAF.
In addition, the previous solution is deprecated in [1] may cause system hang.
[1] https://lore.kernel.org/all/c36ab955-c8db-4a8b-a9d0-f07b5f426c3f@kernel.org |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix use-after free in init error and remove paths
devm_blk_crypto_profile_init() registers a cleanup handler to run when
the associated (platform-) device is being released. For UFS, the
crypto private data and pointers are stored as part of the ufs_hba's
data structure 'struct ufs_hba::crypto_profile'. This structure is
allocated as part of the underlying ufshcd and therefore Scsi_host
allocation.
During driver release or during error handling in ufshcd_pltfrm_init(),
this structure is released as part of ufshcd_dealloc_host() before the
(platform-) device associated with the crypto call above is released.
Once this device is released, the crypto cleanup code will run, using
the just-released 'struct ufs_hba::crypto_profile'. This causes a
use-after-free situation:
Call trace:
kfree+0x60/0x2d8 (P)
kvfree+0x44/0x60
blk_crypto_profile_destroy_callback+0x28/0x70
devm_action_release+0x1c/0x30
release_nodes+0x6c/0x108
devres_release_all+0x98/0x100
device_unbind_cleanup+0x20/0x70
really_probe+0x218/0x2d0
In other words, the initialisation code flow is:
platform-device probe
ufshcd_pltfrm_init()
ufshcd_alloc_host()
scsi_host_alloc()
allocation of struct ufs_hba
creation of scsi-host devices
devm_blk_crypto_profile_init()
devm registration of cleanup handler using platform-device
and during error handling of ufshcd_pltfrm_init() or during driver
removal:
ufshcd_dealloc_host()
scsi_host_put()
put_device(scsi-host)
release of struct ufs_hba
put_device(platform-device)
crypto cleanup handler
To fix this use-after free, change ufshcd_alloc_host() to register a
devres action to automatically cleanup the underlying SCSI device on
ufshcd destruction, without requiring explicit calls to
ufshcd_dealloc_host(). This way:
* the crypto profile and all other ufs_hba-owned resources are
destroyed before SCSI (as they've been registered after)
* a memleak is plugged in tc-dwc-g210-pci.c remove() as a
side-effect
* EXPORT_SYMBOL_GPL(ufshcd_dealloc_host) can be removed fully as
it's not needed anymore
* no future drivers using ufshcd_alloc_host() could ever forget
adding the cleanup |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: lan78xx: Fix double free issue with interrupt buffer allocation
In lan78xx_probe(), the buffer `buf` was being freed twice: once
implicitly through `usb_free_urb(dev->urb_intr)` with the
`URB_FREE_BUFFER` flag and again explicitly by `kfree(buf)`. This caused
a double free issue.
To resolve this, reordered `kmalloc()` and `usb_alloc_urb()` calls to
simplify the initialization sequence and removed the redundant
`kfree(buf)`. Now, `buf` is allocated after `usb_alloc_urb()`, ensuring
it is correctly managed by `usb_fill_int_urb()` and freed by
`usb_free_urb()` as intended. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: Avoid a bad reference count on CPU node
In the parse_perf_domain function, if the call to
of_parse_phandle_with_args returns an error, then the reference to the
CPU device node that was acquired at the start of the function would not
be properly decremented.
Address this by declaring the variable with the __free(device_node)
cleanup attribute. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: af_bluetooth: Fix deadlock
Attemting to do sock_lock on .recvmsg may cause a deadlock as shown
bellow, so instead of using sock_sock this uses sk_receive_queue.lock
on bt_sock_ioctl to avoid the UAF:
INFO: task kworker/u9:1:121 blocked for more than 30 seconds.
Not tainted 6.7.6-lemon #183
Workqueue: hci0 hci_rx_work
Call Trace:
<TASK>
__schedule+0x37d/0xa00
schedule+0x32/0xe0
__lock_sock+0x68/0xa0
? __pfx_autoremove_wake_function+0x10/0x10
lock_sock_nested+0x43/0x50
l2cap_sock_recv_cb+0x21/0xa0
l2cap_recv_frame+0x55b/0x30a0
? psi_task_switch+0xeb/0x270
? finish_task_switch.isra.0+0x93/0x2a0
hci_rx_work+0x33a/0x3f0
process_one_work+0x13a/0x2f0
worker_thread+0x2f0/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe0/0x110
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: base: Free devm resources when unregistering a device
In the current code, devres_release_all() only gets called if the device
has a bus and has been probed.
This leads to issues when using bus-less or driver-less devices where
the device might never get freed if a managed resource holds a reference
to the device. This is happening in the DRM framework for example.
We should thus call devres_release_all() in the device_del() function to
make sure that the device-managed actions are properly executed when the
device is unregistered, even if it has neither a bus nor a driver.
This is effectively the same change than commit 2f8d16a996da ("devres:
release resources on device_del()") that got reverted by commit
a525a3ddeaca ("driver core: free devres in device_release") over
memory leaks concerns.
This patch effectively combines the two commits mentioned above to
release the resources both on device_del() and device_release() and get
the best of both worlds. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: use quiesced elevator switch when reinitializing queues
The hctx's run_work may be racing with the elevator switch when
reinitializing hardware queues. The queue is merely frozen in this
context, but that only prevents requests from allocating and doesn't
stop the hctx work from running. The work may get an elevator pointer
that's being torn down, and can result in use-after-free errors and
kernel panics (example below). Use the quiesced elevator switch instead,
and make the previous one static since it is now only used locally.
nvme nvme0: resetting controller
nvme nvme0: 32/0/0 default/read/poll queues
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 80000020c8861067 P4D 80000020c8861067 PUD 250f8c8067 PMD 0
Oops: 0000 [#1] SMP PTI
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:kyber_has_work+0x29/0x70
...
Call Trace:
__blk_mq_do_dispatch_sched+0x83/0x2b0
__blk_mq_sched_dispatch_requests+0x12e/0x170
blk_mq_sched_dispatch_requests+0x30/0x60
__blk_mq_run_hw_queue+0x2b/0x50
process_one_work+0x1ef/0x380
worker_thread+0x2d/0x3e0 |
| Use after free in Views in Google Chrome prior to 148.0.7778.216 allowed a remote attacker who convinced a user to engage in specific UI gestures to execute arbitrary code via a crafted HTML page. (Chromium security severity: High) |
| Use after free in SVG in Google Chrome prior to 148.0.7778.216 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: High) |
| Use after free in WebGL in Google Chrome prior to 148.0.7778.216 allowed a remote attacker who had compromised the renderer process to potentially perform a sandbox escape via a crafted HTML page. (Chromium security severity: High) |
| Use after free in DOM in Google Chrome prior to 148.0.7778.216 allowed a remote attacker to execute arbitrary code inside a sandbox via a crafted HTML page. (Chromium security severity: High) |
| Rizin is a UNIX-like reverse engineering framework and command-line toolset. There is a double free in librz/core/cmd/cmd_search.c:byte_pattern_search() due wrong pointer ownership declared. This vulnerability is fixed by commit 045fff363b42b8a6dda8ad5229c29ec3267e7dbe. |
