| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
neighbour: Enforce min/max to NDTPA_INTERVAL_PROBE_TIME_MS.
NDTPA_INTERVAL_PROBE_TIME_MS sets .type and .min but misses
.validation_type, so no validation is applied:
# ynl --family rt-neigh --do setneightbl \
--json '{"name": "arp_cache", "parms": {"interval-probe-time-ms": 0}}'
# ynl --family rt-neigh --dump getneightbl --output-json | \
jq '.[] | select(.name == "arp_cache" and has("config"))
| .parms["interval-probe-time-ms"]'
0
Moreover, nla_get_msecs() uses msecs_to_jiffies(), and u64 is
silently cast to u32, so a larger value can bypass the min check:
e.g. 4294967296 == 0x100000000
# ynl --family rt-neigh --do setneightbl \
--json '{"name": "arp_cache", "parms": {"interval-probe-time-ms": 4294967296}}'
# ynl --family rt-neigh --dump getneightbl --output-json | \
jq '.[] | select(.name == "arp_cache" and has("config"))
| .parms["interval-probe-time-ms"]'
0
msecs_to_jiffies() returns MAX_JIFFY_OFFSET if the value is
larger than INT_MAX. Also, INT_MAX ms overflows int NEIGH_VAR()
when HZ > 1000 (Alpha, MIPS), and passing a negative integer to
queue_delayed_work(unsigned long delay) causes sign extension,
which wraps around the expiry time to the past, resulting in it
being handled as 0 delay in the timer wheel.
Let's use NLA_POLICY_FULL_RANGE() and limit the max to 1 day.
The same max check is applied to sysctl as well.
Note that this controls the probe interval for NTF_MANAGED
entries, so the max of 1 day is unlikely to break any
deployments. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: don't get the radio mask for netdev-less wdevs
cfg80211_calculate_bi_data() calls rdev_get_radio_mask() with
wdev->netdev, which can be NULL and then crashes in mac80211.
To avoid that, invert the order of checks since wdev->netdev
is always valid for beaconing interfaces. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: mesh: reset the CSA state when leaving
ifmsh->csa is allocated in ieee80211_mesh_csa_beacon() and only freed
in ieee80211_mesh_finish_csa(), i.e. when the channel switch completes.
Leaving the mesh while a switch is still pending therefore leaks it.
Additionally, ifmsh->csa_role and ifmsh->chsw_ttl have their state leak
in this case, so things can get mixed up in addition to the memory
leak.
Refactor the reset and call it in ieee80211_stop_mesh() to fix it all. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix null pointer access in is_include_guest_event()
A typical module unload occurring event when there is an active perf
connection leads to freeing of the pmu pointer. The call log is something
like:
..
__pmu_detach_event
pmu_detach_event
pmu_detach_events
perf_pmu_unregister
..
__pmu_detach_event() sets event->pmu to null. When the perf connection
finally is closed, the following stack trace is observed:
Oops: general protection fault, kernel NULL pointer dereference
...
RIP: 0010:_free_event+0x3e/0x370
...
Call Trace:
...
perf_event_release_kernel+0x260/0x2d0
perf_release+0x12/0x20
A call to mediated_pmu_unaccount_event() inside _free_event() is the root
cause of this crash. Adding a check inside is_include_guest_event() ensures
we don't accidentally access a null pmu ptr. In addition to this, we will
now call mediated_pmu_unaccount_event() before clearing the pmu ptr so that
nr_include_guest_events counts are maintained correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: ibss: ref BSS entry for joined event
When the IBSS is joined, we only record the BSSID/channel in the event
and look up the BSS entry when processing it. However, that's racy,
e.g. a new scan with NL80211_SCAN_FLAG_FLUSH can remove it, causing a
warning in the event work:
!bss
WARNING: net/wireless/ibss.c:37 at __cfg80211_ibss_joined+0x3d3/0x440
Workqueue: cfg80211 cfg80211_event_work
cfg80211_process_wdev_events+0x39f/0x5b0 net/wireless/util.c:1144
cfg80211_process_rdev_events+0xa1/0x110 net/wireless/util.c:1179
cfg80211_event_work+0x2f/0x40 net/wireless/core.c:393
Do the lookup early (the driver is expected to only join an IBSS that
has a BSS entry) and keep a reference to it. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) increase number of phases and add new mask
Increase the number of phases to 16 as a new upcoming device supports
such a number.
While at it, add a new mask for controlling the source of the output
voltage.
Note (groeck):
This patch was meant to prepare for support of MAX20826 and compatible
devices, which support more than 10 phases per page. However, Sashiko
reports that the mp2975 driver already supports up to 14 phases, and the
mp2856 driver supports up to 12 phases. This already has the potential for
out-of-bounds writes when probing the affected chips, making this patch a
bug fix. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: soc_button_array - check btns_desc->package.count
Check that btns_desc->package.count is not 0 before accessing
btns_desc->package.elements[0]. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: handle lack of space when cleaning up verity items
When enable_verity() hits the qgroup limit, rollback_verity() needs its
own metadata reservation. When the qgroup limit or lack of space refuses
the rollback, the whole filesystem is forced read-only even though the
qgroup limit was for one subvolume only. Also orphan cleanup at the next
mount fails the same way, so the leftover items are never removed: with
-EDQUOT the subvolume stays unreachable, and with -ENOSPC on a full
filesystem the next read-write mount fails.
Start transactions with btrfs_start_transaction_fallback_global_rsv() in
btrfs_orphan_cleanup(), drop_verity_items() and rollback_verity(). Those
calls only delete items and free the space in the end, so they may use
the global reserve and skip the qgroup limit, which avoids -ENOSPC and
-EDQUOT. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: set up the TX info early to fix failure paths
The previous commit 2c51457d930f ("wifi: mac80211: free ack status
frame on TX header build failure") cleaned up the leak, but still
left the code a bit messy and the failed SKB didn't get reported
to userspace.
Fix this up by initialising skb->cb[] earlier, which allows using
ieee80211_free_txskb() and therefore reports it for the failure
in ieee80211_build_hdr(), and unifies the ieee80211_skb_resize()
failure path with it. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: atr: fix dangling adapter pointer on add failure
i2c_atr_add_adapter() stores atr->adapter[chan_id] before
i2c_add_adapter() so that the I2C bus notifier can match child clients
during registration. On failure the channel is freed but the slot was
left pointing at freed memory, which can lead to use-after-free in
i2c_atr_del_adapter() / cleanup and also block reuse with -EEXIST.
Clear the slot on the i2c_add_adapter() error path before freeing chan. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: refuse to make a monitor active when it has no queue
A monitor interface only gets a TXQ if it's created active, and one can't
be added later. Setting the flag on a down interface is still allowed, so
the driver is handed a monitor with no queue. ath9k dereferences it:
BUG: kernel NULL pointer dereference, address: 0000000000000066
RIP: 0010:ath_tx_node_init+0x49/0x170 [ath9k]
ath9k_add_interface+0x10c/0x140 [ath9k]
drv_add_interface+0x54/0x250 [mac80211]
ieee80211_do_open+0x32f/0x800 [mac80211]
Reached with CAP_NET_ADMIN by "iw dev X set monitor active" followed by
"ip link set X up". RTNL is held, so netlink operations block behind it.
Refuse the flag when there is no queue to give. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: avoid out-of-bounds read for empty PREQ elements
ieee80211_mesh_preq_size_ok() derives the location of the PREQ bottom
fields before checking whether the element contains even the fixed
header. ieee80211_mesh_hwmp_preq_get_bottom() reads the flags byte to
account for the optional Address Extension field. Consequently, an
empty PREQ element causes a one-byte read beyond its declared payload.
Move the helper call after both size checks, so the bottom fields are
only accessed when they are present. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: p54: require a full exp_if record in PDR_INTERFACE_LIST
The PDR_INTERFACE_LIST loop only checks that the record start is within
the entry before reading an entire struct exp_if from it. A truncated
trailing record makes the if_id/variant reads cross the entry boundary
into the heap beyond the EEPROM buffer (verified with a KASAN
reproducer of the loop). The variant also feeds the synth front-end
selection, so this is not only a leak.
Advance only while a full record still fits in the entry. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Serialize local codec list cleanup
hci_dev_close_sync() clears hdev->local_codecs after releasing hdev->lock.
Codec list additions and both traversals in sco_sock_getsockopt() use that
lock, but the close path does not. A close and BT_CODEC query can therefore
interleave as follows:
hci_dev_close_sync() sco_sock_getsockopt()
hci_dev_lock()
fetch codec entry
hci_codec_list_clear()
kfree(entry)
read entry->id
The reader then accesses an entry which the close path has freed. KASAN
BUG: KASAN: slab-use-after-free in sco_sock_getsockopt+0xfa0/0xfe0
Read of size 1 at addr ffff8881001c3450
Call Trace:
sco_sock_getsockopt+0xfa0/0xfe0
do_sock_getsockopt+0x537/0x7b0
__sys_getsockopt+0xf2/0x170
Allocated by task 92:
hci_codec_list_add.isra.0+0x2c/0x440
hci_read_codec_capabilities+0x224/0x590
hci_read_supported_codecs+0x2c2/0x640
Freed by task 92:
kfree+0x131/0x3c0
hci_codec_list_clear+0xd8/0x160
hci_dev_close_sync+0x92a/0xfa0
Take hdev->lock around the clear operation at its existing point in the
close path. This makes the clear wait for active readers and prevents a new
traversal until the list is empty without changing teardown ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: add HE 6 GHz capability in the scan elems len
The HE 6 GHz Band Capability element is in the probe request for
every band if 6 GHz is supported, so add the size to scan_ies_len.
Otherwise, building probe request elements can fail, triggering the
WARN_ON in __ieee80211_start_scan(). |
| In the Linux kernel, the following vulnerability has been resolved:
Input: rmi_smbus - fix out-of-bounds read in rmi_smb_write_block()
When chunking writes into SMBus blocks in rmi_smb_write_block(), the
loop calculates block_len using the original total length (len) instead
of the remaining length (cur_len).
If len is greater than 32 bytes (SMB_MAX_COUNT), block_len remains 32
for every iteration, even on the final partial chunk where fewer than 32
bytes remain. This causes smb_block_write() to read 32 bytes from the
advanced data buffer pointer, reading past the end of the input buffer.
Fix this by calculating block_len using cur_len and advancing the buffer
and address pointers by block_len. |
| Use after free in Microsoft Edge (Chromium-based) allows an authorized attacker to execute code over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmsmac: fix UAF in brcms_free_timer()
brcms_free_timer() calls brcms_del_timer() which uses the non-synchronous
cancel_delayed_work() to cancel the timer's underlying delayed work. If
the work callback (_brcms_timer) is already running, cancel_delayed_work()
returns false without waiting, and brcms_free_timer() proceeds to kfree(t)
while the callback still accesses t through container_of().
Add an explicit cancel_delayed_work_sync() after brcms_del_timer() to
guarantee that any in-flight callback has completed before the timer
structure is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - fix GPF in suspend and resume when unbound
Transport drivers (such as rmi_i2c and rmi_spi) invoke
rmi_driver_suspend() and rmi_driver_resume() on their child rmi_dev
device during system power management events. However, transport drivers
are fully registered and operational even if the physical RMI driver
failed to bind or probe the rmi_dev device.
When rmi_driver_suspend() or rmi_driver_resume() is called on an unbound
rmi_dev, dev_get_drvdata() returns NULL. Calling rmi_disable_irq() or
rmi_enable_irq() without driver data attached causes a NULL pointer
dereference and General Protection Fault when attempting to lock
data->enabled_mutex.
Fix this by checking if driver data is attached to rmi_dev in
rmi_driver_suspend() and rmi_driver_resume(), exiting early if
no driver data is present. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: Validate MODE SENSE lengths in scsi_cdl_enable()
scsi_cdl_enable() uses length fields returned by MODE SENSE to locate
the ATA feature mode page in a 64-byte stack buffer. A target can report
a total length shorter than its mode header and block descriptors. The
unsigned subtraction used for the MODE SELECT length can wrap, and the
separately computed buf_data can point beyond buf.
During automatic scan, enable is false, so the read-modify-write of
buf_data[4] can clear the low two bits of a target-selected
out-of-bounds stack byte. scsi_mode_select() can then copy up to 64
bytes from outside the buffer into the outgoing MODE SELECT payload,
disclosing stack contents to the target.
This is reachable while scanning a USB storage device that identifies as
an ATA device and advertises CDL support. No filesystem mount or
userspace access to the block device is required.
On upstream commit cee9395acd80 ("Linux 7.3-rc1"), a build-specific,
one-vCPU QEMU/Raw Gadget proof using QEMU-only multi-UDC allocator
sampling executed a fixed proof command inside the guest and created a
UID-0-owned marker during automatic enumeration, with KASLR and NX
enabled.
The issue was independently found during security research at Drivesec
S.r.l.
Cap the available length to the buffer size. Validate and consume the
mode header and block descriptor lengths before using the page, and
require the five bytes needed to access the CDL field. |
